What Are SPI Surface Finish Standards?
The SPI (Society of the Plastics Industry, now PLASTICS Industry Association) surface finish standards are the universal language for specifying mold cavity polish levels. Introduced decades ago as a way to standardize communication between product designers and toolmakers, the SPI system divides finishes into four grades — A, B, C, and D — each with three sub-levels. Grade A represents the highest gloss, diamond-polished surfaces, while Grade D denotes coarse blasted textures. Every mold maker worldwide who’s worth their salt understands these designations, making SPI the default reference system in technical drawings, RFQs, and quality inspection reports across the injection molding supply chain.

Getting the finish specification right affects appearance, demolding, tooling work and maintenance. A high polish and a blasted texture involve different work, but their cost and service interval depend on the mold steel, area, access, geometry, resin and production conditions. Use the grade chart to communicate the finish, then ask for a quotation against defined surface zones and approved sample or measurement requirements.

For the tooling layout behind these surface requirements, review ontwerp van kern en holte.
SPI Grade A: Diamond Polish Finishes
A-group preparation uses diamond compounds of progressively finer grades. The result depends on tool steel, starting surface, geometry and access for polishing. Agree any roughness and optical acceptance requirements separately from the SPI designation; confirm the molded sample in the specified resin and color.
For A-grade finishes, distinguish cosmetic appearance from optical performance and review accessible polishing areas, cavity geometry, steel condition and future maintenance. Re-polishing may affect critical dimensions, so agree how the tool and molded samples will be checked after finish work. Compare A-1 and A-2 against the actual optical or appearance requirement rather than a universal price premium or service interval.
SPI Grade B: Fine Semi-Gloss Finishes
Grade B finishes use grit paper rather than diamond compound, producing semi-gloss surfaces suitable for most consumer-facing parts. B-1 uses 600-grit paper for Ra 0.05-0.10 μm, B-2 uses 400-grit for Ra 0.10-0.15 μm, and B-3 uses 320-grit for Ra 0.15-0.28 μm. These are the workhorse finishes of injection molding — roughly 60% of all consumer product cavities ship with B-1 or B-2 finish. The semi-gloss appearance hides minor flow lines, blush marks, and sink that would be glaring on an A-grade finish while still delivering a premium look that satisfies most consumer expectations.
B-group preparation uses abrasive paper. Select the grade by the required appearance and approved reference, then quote polishing area, cavity count and maintenance separately. A fixed premium or number of shots cannot be promised from the finish designation alone.
SPI Grade C and D: Textured and Matte Finishes
C-group preparation uses abrasive stones; D-group preparation uses dry blasting. The reference abrasive becomes coarser across the respective subgrades. These descriptions concern mold preparation: molded appearance also depends on resin, filler, color and processing. Use the referenced preparation guide and an approved sample rather than inferring a guaranteed part roughness.
Textured surfaces can require more draft to release reliably. Review texture depth, draw direction, wall geometry, resin and the toolmaker’s recommendation together. Do not add a fixed number of degrees to every D-grade texture; resolve release and appearance before cutting the production tool.
| SPI designation | Preparation reference | Purchasing requirement |
|---|---|---|
| A-1 | Diamond compound, grade 3 | Agree the reference sample and any separately required Ra. |
| A-2 | Diamond compound, grade 6 | Agree the reference sample and any separately required Ra. |
| A-3 | Diamond compound, grade 15 | Agree the reference sample and any separately required Ra. |
| B-1 | Paper, 600 grit | Agree the reference sample and any separately required Ra. |
| B-2 | Paper, 400 grit | Agree the reference sample and any separately required Ra. |
| B-3 | Paper, 320 grit | Agree the reference sample and any separately required Ra. |
| C-1 | Stone, 600 grit | Agree the reference sample and any separately required Ra. |
| C-2 | Stone, 400 grit | Agree the reference sample and any separately required Ra. |
| C-3 | Stone, 320 grit | Agree the reference sample and any separately required Ra. |
| D-1 | Glass-bead dry blasting | Agree the reference sample and any separately required Ra. |
| D-2 | Oxide dry blasting, 240 grade | Agree the reference sample and any separately required Ra. |
| D-3 | Oxide dry blasting, 24 grade | Agree the reference sample and any separately required Ra. |
The preparation groups below are summarized from the DME mold-finish guide en Autodesk mold-surface sheet. These publications give different or incomplete approximate Ra mappings. Specify numeric roughness, measurement method and sample acceptance separately; a grade label is not a universal finished-part Ra guarantee. Cost and maintenance life require a tool-specific quotation.
Recensie chamfer and fillet design for molded parts when the appearance requirement extends across edges and corners.
Material-Finish Matching: Which Finish for Which Resin
Mold finish and molded appearance are different specifications. Resin structure, fillers, color and process conditions affect how a polished or textured cavity appears on the part. Filled resins can show fibers at the surface, but a single B-grade ceiling is not valid for every compound. Approve representative molded samples rather than assuming one grade guarantees the same gloss in all materials.
The material-finish matching matrix also works in reverse: some materials need a specific minimum finish to function properly. Silicone and TPE adhere so aggressively to polished surfaces that B-1 or better is essentially mandatory for demolding without tearing. POM’s low friction coefficient means it releases well from any finish, but a B-2 or better cavity surface is recommended to minimize squeaking in moving parts. For overmolding applications, the substrate surface should be C-1 or rougher to provide mechanical tooth for the overmold bond — a polished substrate surface leads to delamination failures in the field. When specifying finishes, communicate your material choice to the toolmaker; they’ll flag incompatible combinations before steel is cut.
- Specify SPI Finish on Every Drawing: Always call out the finish grade (e.g., “SPI B-2” or “SPI A-3”) directly on the cavity surface annotation. Never rely on verbal instructions or assume the toolmaker’s default; a missing finish spec defaults to “as machined,” which has Ra 0.8-1.6 μm.
- Match Finish to Material Capability: Don’t specify A-1 on a GF nylon part — the glass fibers limit you to B-3 at best. Check the material’s maximum achievable finish before writing the spec to avoid paying for polish that the plastic cannot replicate.
- Add 1° Draft per 0.025mm of Texture Depth: Every SPI texture grade beyond B-1 requires draft angle compensation. A D-2 blasted mold running ABS needs roughly 5.5-6° of draft — factor this into your part geometry before it reaches the tool designer.
- Separate Cosmetic and Functional Zones: Call out different finishes for different regions of the same part. The visible A-side might be B-1 while ribs and bosses on the B-side remain D-2. This saves $200-400 per cavity by limiting premium polishing to surfaces customers actually see.
- Verify with a Surface Roughness Tester: Ra values aren’t subjective — demand profilometer readings during first article inspection. A $300 portable tester confirms whether the toolmaker actually delivered SPI B-1 (Ra 0.05-0.10 μm) versus a “close enough” B-2 (Ra 0.10-0.15 μm).
- Budget for Re-Polishing in Tool Life Planning: A-grade finishes lose spec after 50K-100K shots. If your program runs 500K parts, budget for 5-10 re-polish cycles at $300-800 each, and account for the cumulative 0.01-0.05mm of steel removal in your tolerance stack.

Toepassingsmatrix voor de industrie
| Industrie | Common SPI Grades | Typisch materiaal | Primary Requirement | Inspection Method |
|---|---|---|---|---|
| Optical Components | A-1, A-2 | PC, PMMA | Light transmission >90% | Profilometer + haze meter |
| Consumentenelektronica | A-3, B-1 | PC/ABS, ABS | Premium feel + scratch resistance | Visual under 500 lux |
| Auto-interieur | B-2, C-1 | PP, PC/ABS | Low gloss for glare reduction | Gloss meter at 60° angle |
| Industriële behuizingen | D-1, D-2 | GF Nylon, PC | Durability + defect hiding | Visual comparison plaques |
Cost Decision Framework: SPI Finish Grade Economics
Surface finish directly impacts three cost drivers — initial tooling, cycle time, and maintenance. Here’s how finish grade affects your total cost of ownership across production volumes:
- Prototype / Bridge Tooling (1-5K parts): Use B-3 or as-machined finish. The $200-500 savings per cavity doesn’t justify premium polishing for low-volume validation. Expect visible tool marks but functional parts.
- Low-Volume Production (5K-50K parts): B-2 is the sweet spot. One polish cycle lasts the entire production run on P20 steel, and the semi-gloss finish satisfies 90% of consumer product requirements. Total finish cost: $200-400 per cavity, zero re-polish expense.
- Mid-Volume Production (50K-250K parts): A-3 for cosmetic surfaces, B-2 for everything else. Budget for one re-polish at 150K shots ($400-600). If optical clarity is required, A-1 on the critical surface only — not the entire cavity.
- High-Volume Production (250K+ parts): Hardened steel (52+ HRC) with A-2 finish for cosmetic, B-1 for functional. Re-polish every 100K-150K shots on hardened steel, 50K-75K on P20. Each re-polish round costs $500-800 per cavity including downtime. Over 1M shots, total finish maintenance can reach $4,000-8,000 per cavity — factor this into your piece price from day one.
A-grade polish costs $30-60/hour for skilled labor. A typical consumer product cavity takes 12-16 hours for A-1, 8-10 hours for A-2, and 4-6 hours for A-3. The labor component alone explains the cost hierarchy — finish grade is literally paid for in hours of a polisher’s time.
Keep the appearance reference separate from dimensional acceptance; the richtlijn voor toleranties van kunststofonderdelen covers drawing and inspection requirements.
Common Surface Finish Defects and Solutions
| Defect | Oorzaak | Oplossing |
|---|---|---|
| Orange Peel Texture | Over-polishing with wrong technique — excessive pressure causes surface waviness instead of smoothness | Re-polish using progressive grit steps without skipping grades (400→600→800→1200, never 400→1200). Reduce polishing pressure to 5-10 N and verify with profilometer between steps. |
| Sink Marks Visible Through Polish | High-gloss finish amplifies even 0.005mm of sink (vs 0.02mm threshold on C-grade) | Reduce rib thickness to 50% of wall. Increase packing pressure 15-25% and extend hold time 2-3 seconds. If persistent, downgrade to A-3 or B-1 — semi-gloss hides sink 4× better than mirror polish. |
| Scratch Marks After Short Runs | Soft mold steel (below 40 HRC) paired with abrasive material like glass-filled resin | Upgrade to hardened steel (48-52 HRC) or stainless (S136 at 50-54 HRC). Apply TiN or CrN coating (0.003-0.005mm) for added abrasion resistance on GF materials. Expect coating to add $300-600 per cavity. |
| Inconsistent Gloss Across Part | Uneven polishing pressure in contoured areas or differential mold temperature during molding | Use conformal cooling to maintain mold surface temperature within ±3°C across the cavity. Verify polish uniformity with a gloss meter at multiple positions (aim for ±5 GU variation on A-grade). Re-polish problem areas with specialized contour tools. |
Finish examples, left to right
- Automotive trim
SPI A2 · High gloss - Medical device housing
SPI B1 · Semi-gloss - Consumentenelektronica
SPI C1 · Soft matte - Industrial tool housing
SPI D2 · Textured
These examples illustrate appearance. Confirm the finish against a physical sample in the selected resin.
In één oogopslag
| Beslissingsmoment | SPI Finishes | Opmerking voor de koper |
|---|---|---|
| A group | Hoogglans | Use when appearance is the priority |
| B group | Paper-prepared finish | Balance appearance and tooling cost |
| C group | Ground finish | Good for general functional parts |
| D group | Textured / matte | Helps hide wear and molding marks |
Veelgestelde vragen
Waar staat SPI voor bij spuitgieten?
SPI staat voor de Society of the Plastics Industry (tegenwoordig de PLASTICS Industry Association genoemd). De SPI-norm voor oppervlakteafwerking bestaat uit een reeks van 12 vastgestelde polijstgraden voor matrijzen (A-1 tot en met D-3), waarin de methode, het type schuurmiddel en de resulterende waarde voor de oppervlakteruwheid (Ra) worden gespecificeerd. Overal ter wereld verwijzen fabrikanten van spuitgietmatrijzen in technische tekeningen naar SPI-kwaliteiten om het vereiste polijstniveau van de holtes aan te geven. De norm werd oorspronkelijk gepubliceerd als de „SPI-SPE Mold Finish Guide“ en blijft de de facto wereldwijde norm, ook al heeft de organisatie haar naam veranderd.
What’s the best surface finish for clear polycarbonate parts?
For clear polycarbonate optical components (lenses, light pipes, transparent enclosures), SPI A-1 or A-2 is essential. A-1 delivers Ra 0.012-0.025 μm — true mirror quality — and is required for lenses where any surface imperfection distorts light transmission. A-2 (Ra 0.025-0.05 μm) works well for general transparent housings and covers where minor surface imperfections are tolerable. For non-optical clear parts like protective covers, A-3 often suffices. Keep in mind that PC’s inherent light transmission of 88-92% means no amount of polishing can make it as clear as glass (99%+), and any contamination or moisture in the resin degrades clarity independently of mold finish.
Hoeveel bedraagt de meerprijs van A-kwaliteit polijstmiddel ten opzichte van de gereedschapskosten?
There is no reliable fixed premium per cavity without reviewing the tool and finish requirement. Cost changes with mold steel and hardness, polishing area, cavity count, part geometry, starting surface condition, optical or cosmetic acceptance criteria, access for hand polishing and future maintenance. For a comparable quotation, mark each cosmetic zone on the drawing, state the required SPI grade or approved sample, identify the resin and color, and ask for finish work as a separate tooling line item.
Kunnen er verschillende SPI-afwerkingen op hetzelfde onderdeel worden toegepast?
Yes — this is standard practice and strongly recommended for cost optimization. The cavity (A-side, cosmetic face) typically gets the premium finish (B-2 to A-2), while the core side gets a functional finish (C-1 to D-2) since it’s usually hidden from view. On a single drawing, annotate each surface: “SPI B-2 — Cosmetic Face A” and “SPI D-2 — Non-Cosmetic Surfaces” or designate specific zones. The cost savings are substantial — polishing only the visible A-side rather than the entire cavity reduces finishing labor by 40-60%. Just ensure your drawing clearly delineates the finish boundary lines so the toolmaker knows exactly where each finish applies.
Gerelateerde lezen
- Plastic Welding Methods ComparedUltrasonic, hot plate, and laser welding techniques
- Normen voor oppervlakteafwerking van bewerkte onderdelen: Complete gids
- CNC-bewerking versus spuitgieten: een uitgebreide vergelijking van de productiemethoden
- CNC verspanen vs. spuitgieten: Hoe het juiste proces te kiezen voor kunststof onderdelen
Request an SPI Finish and Mold Review
Use this review when a drawing calls out an SPI finish, when an appearance sample must be translated into a mold requirement, or when finish choice is affecting release, gloss, visibility of flow marks or tooling cost.
How do SPI surface finish standards become a clear tooling requirement?
Assign the required finish to specific drawing zones and provide a physical or approved visual reference where appearance is critical. Identify resin, color, draft, parting line and gate restrictions. The quotation should distinguish mold polishing or texturing from secondary part finishing, and state how molded samples will be approved. An SPI label alone does not guarantee the same appearance in every resin.
- Appearance target: Requested SPI grade, approved sample or texture reference, gloss target and cosmetic zones.
- Part and resin: 2D drawing or CAD, resin and color, wall thickness, critical surfaces and expected defects to avoid.
- Tooling status: New mold, mold modification or production issue, plus cavity count and the current tool stage.
- Commercial scope: Prototype or production quantity, annual volume, destination and target timing.
The review can identify: a suitable SPI grade or alternative, resin-and-finish compatibility concerns, drawing or sample questions, inspection references and the tooling or molded-part scope that should be quoted.
Mark finish boundaries, mold parting line and gate restrictions; define whether acceptance is visual, a measured texture, gloss, haze or another stated requirement. Agree the reference sample, lighting or measurement method and the sample approval stage.
Final finish selection and pricing depend on the approved appearance reference, resin, mold steel, part geometry, polishing area, cavity count, tool condition and inspection requirement.



