Stanyl PA46 is een polyamide voor hoge temperaturen dat wordt gebruikt in toepassingen waarin conventioneel PA66 mogelijk te veel aan stijfheid of slijtvastheid inboet. De keuze van de kwaliteit hangt nog steeds af van de wapening, de conditionering, de langdurige belasting, de temperatuur en het verwerkingsvenster; de onderstaande waarden moeten worden getoetst aan het actuele gegevensblad van de leverancier voor de exacte kwaliteit.
Voor engineering- en inkoopteams
Overweegt u Stanyl PA46 te gebruiken voor een onderdeel dat aan hoge temperaturen wordt blootgesteld?
PA46 is een polyamidevariant voor hoge temperaturen wanneer het behoud van stijfheid en de weerstand tegen slijtage en vermoeidheid bij hoge temperaturen een strengere controle van het droog- en gietproces rechtvaardigen.
- Vergelijk de exacte kwaliteit in droge en geconditioneerde toestand
- Controleer de gemiddelde temperatuur, de piektemperatuur en de belasting afzonderlijk
- Bekijk de alternatieven voor PA66, PPA en PPS voordat je het ontwerp van het gereedschap definitief vastlegt
Request a PA46 grade and molding review → Bekijk technische kunststoffen voor hoge temperaturen

Stanyl PA46 Datasheet Example
Envalior identifies Stanyl TW200F6H as PA46-GF30. The manufacturer publishes the following values for this grade. Use the processing and mechanical data for the exact variant on the quotation.
| Measure | TW200F6H | How to use it |
|---|---|---|
| Melting temperature | 295°C at a heating rate of 10°C/min | Material characterization. Use the grade processing sheet for melt and mold settings. |
| Vervormingstemperatuur onder belasting | 290°C at 1.80 MPa | Short-term specimen test. Establish sustained service temperature from the part duty cycle and retained properties. |
| Burning behavior | HB at the stated 1.5 mm and 3.0 mm test thicknesses | Check exact grade, thickness, color and recognition separately for a flame-rated specification. |
Select reinforcement by load, impact, creep, mold filling and dimensional requirements. Higher nominal fiber content alone cannot establish how a different grade will perform in the actual part.
PA46 vs PA66 vs PPA vs PPS: Vergelijking van nylonsoorten voor hoge temperaturen

| Candidate | When to compare it | Evidence to bring to the review |
|---|---|---|
| PA46 | Retained stiffness, wear or fatigue at elevated temperature | Temperature-dependent data and testing at the actual duty cycle and conditioning state |
| PA66 | An existing production baseline or a general reinforced grade | Baseline service margin, conditioned fit and heat aging |
| PPA | A specified semi-aromatic polyamide is under consideration | Exact formulation, conditioning, chemical and heat-aging evidence |
| PPS | Chemical exposure or high-temperature dimensional requirements dominate | Grade-specific creep, impact, chemical compatibility and molding feasibility |
Stanyl PA46-selector voor commercieel gebruik
Gebruik de Envalior Stanyl portfolio to find candidate grades for wear, heat stabilization or electrical use. The exact designation matters. For example, TW200F6H and TW200F6 are distinct catalogue entries. Request the current datasheet and part-specific documentation for the grade quoted.
Verwerking van PA46: Spuitgietparameters
| Process item | Wat moet worden bevestigd? |
|---|---|
| Drying and material handling | Supplier drying profile, permitted moisture content and protected feed conditions |
| Melt, mold and residence time | Current grade limits and a machine and mold rated to run within them |
| Fill, pack and cool | Gate, venting, weld lines and measured fit on representative samples |
| Part approval | Dry and conditioned dimensions, relevant mechanical tests and acceptance criteria |
PA46-toepassingen per sector


| Application to screen | Evidence before approval |
|---|---|
| Gear, guide or bearing cage | Load, speed, lubricant, temperature and wear on the actual pair |
| Hot-side housing or connector | Heat cycle, sustained stress, chemical exposure and assembled fit |
| Electrical housing or bobbin | Service temperature, wall thickness, electrical duty and grade-specific documentation |
PA46 FR (vlamvertragend) kwaliteiten
For a flame-rated component, obtain the current listing for the exact grade, color and minimum tested thickness. Check required electrical or glow-wire documents separately. Assess reflow, dimensional change and weld lines on the actual molded part when those requirements apply.
When to Compare Alternatives
Compare alternatives if the molding equipment cannot run the grade, if humidity creates unacceptable fit change, or if a proposed grade lacks the required aged, electrical or chemical evidence. Ask for the quotation and validation plan before changing a released material.
Wat is PA46?
PA46 is an aliphatic polyamide. Stanyl is Envalior’s PA46 product family. Candidate grades are available with different reinforcement and stabilization systems, so the family name alone does not identify the material used for a test result.
Compare Stiffness Retention at Service Temperature
Temperature-dependent modulus data can help screen materials for stiffness retention. Compare the method, frequency or load, conditioning and specimen geometry. For a part that carries load over time, also request creep, heat aging and the acceptance limit for the relevant interface.
PA46 GF30 versus GF40: eigenschappen van met glas gevulde typen
Compare the exact GF30 and GF40 grades against the service load, impact requirement and molding route. Use equivalent conditioning and test direction. Check thin walls, weld lines and mating geometry on the sample before tooling approval.
Veelgestelde vragen
Waarin verschilt Stanyl PA46 van PA66?
Some PA46 grades offer useful stiffness retention and wear performance at elevated temperatures. Compare exact formulations with their condition and test method stated.
Bij welke temperatuur presteert PA46 beter dan PA66?
There is no single crossover temperature. Compare retained stiffness, impact or wear after the same heat and humidity exposure and at the intended load.
Is Stanyl PA46 duurder dan PA66?
Request quotes for the actual grades, quantities, supply terms and process. Compare piece cost and qualification requirements after screening performance.
Wat zijn de belangrijkste uitdagingen bij de verwerking van PA46?
Follow the grade’s drying, melt, mold and residence-time limits. Confirm the press and mold can achieve them and validate dimensions and weld-line performance on samples.
Wat moet uit een beoordeling van de PA46-kunststofkwaliteit blijken voordat er een bestelling wordt geplaatst?
Send the grade and drawing, continuous and peak heat, dwell time, mechanical load, moisture or fluids, electrical duty and quantities. Agree what evidence will approve the material and first parts.
Technische bronnen en verificatie
Gebruik leveranciersgegevens als verificatiebron, maar niet als vervanging voor het testen van de exacte kwaliteit en het exacte onderdeel onder de beoogde gebruiksomstandigheden.
Last updated: June 2026. Datasheet values are typical ranges for standard Stanyl grades. Always verify specific grade properties with the manufacturer’s current technical data sheet. Stanyl is a registered trademark of Envalior (formerly DSM Engineering Materials).
PA46: Toelichting bij de selectie
| Materiaal | Sterk punt | Waarschuwing voor kopers |
|---|---|---|
| PA46 | Hoge hittebestendigheid en uitstekend behoud van stijfheid | Controleer de vochtigheidsregeling en de vormingsperiode |
| PA66 | Grotere beschikbaarheid en uitstekende prestaties voor algemene doeleinden | Meestal een kleinere temperatuurmarge dan PA46 |
| PBT | Goede maatvastheid en elektrische eigenschappen | Niet ideaal wanneer aanhoudende hitte en vermoeidheid de boventoon voeren |
Waarom kiezen voor nylon?
Nylon Plastic biedt een selectie van nylonsoorten die bestand zijn tegen hoge temperaturen, voor kopers die vóór het indienen van een offerteaanvraag een praktische vergelijking willen maken tussen PA46, PA66 en andere technische thermoplasten.
Gerelateerde lezen
- PPA-gids voor polyftalamide: PA6T, PA9T en PA10T – soorten, eigenschappen en een vergelijking met PA66 en PA46
- Handleiding voor waterstraalsnijden: hoe snijden met water onder hoge druk werkt
- PA6-materiaal: complete gids over de eigenschappen, verwerking en toepassingen van nylon 6
- SAE PA66: de complete gids
- Volledig technisch naslagwerk over de eigenschappen van nylon
- Nylon versus polycarbonaat


